Pavilion roof cover - step by step

Pavilion roof cover - step by step


A pavilion provides a cozy atmosphere. Homebuilding can succeed, but to cover the polygonal roof is a challenge for home improvement.

1. Material Selection - The Right Roof Type for a Pavilion

Before you can lay the garden pavilion, the do-it-yourselfer picks the right materials. The roof of a pavilion is usually polygonal and runs in the middle of a pyramid-like. The DIY store offers PVC finished roof variants in various sizes for screwing onto the undercarriage.

The most common roof variant for DIY construction is the roof made of bitumen roofing board due to its customizability and resistance. The do-it-yourselfer needs a pre-tarpaulin, bitumen shingles, hammer and nails for this brick-look type of roof. Just as important are drills, screws, eaves moldings and eaves pieces made of corrosion-resistant stainless steel. With a roof slope of 60 percent or more, bitumen adhesive is required.

2. Roof area calculation according to Pythagoras

In order to determine the material requirement, the handyman reaches for the yardstick and measures the roof. In this way he determines the dimensions for eaves and eaves moldings.

For the total area calculation, he takes the root from the height of the roof in square plus the base area in square. From the result, he subtracts the square from the base divided by two. If he pulls the root out of it, he gets the height of a single roof side, which he divides by two. The result is multiplied by the base area and preserves the area of ​​a single roof side. For the total roof area, multiply this single page by the number of pavilion corners.

3. Material requirements determination - consider overlap

The result from the area calculation corresponds to the total roof area. The required cover tarpaulin for the planned work must be around ten centimeters larger than the total roof area. Once again, bitumen shingles are needed in the total roof area by two because the roofing felt is laid overlapping. If you want to get an overview of the total price of the materials, then take the calculated square meters three times.

4. Fastening the pre-cover tarpaulin and eaves parts to the roof

The handyman screws a matching eaves part at the bottom of each polygon surface. The insulating cover tarpaulin is laid parallel to the eaves over the entire roof surface. He fastens them with nails with a horizontal overlap of ten centimeters above the eaves. The Traufleisten are bolted to the side edges on the Vordeckplane. Do not save on screws and nails. The steeper the roof, the more fastenings are required.

5. Prepare the initial row of bituminous roofing paper

After laying the canopy cover, the do-it-yourselfer nails the beginning row of bitumen cardboard onto the roof of the pavilion. He shortens the shingle fangs in the first row until the end of the leaf incision. The shingle he puts out a few millimeters above the eaves and the edges and in length he cuts by half a tongue. The first row does not hit the next row with the butt joint.

6. Lay the nails with the nails

When mounting, nails should be two centimeters above the blade incisions and two to three centimeters from all sides. All nail heads are flush after a straight hit. Use more nails on steep roofs and do not forget to glue with bituminous glue.

7. Fastening following rows

The following series of roof shingles starts with a complete shingle. The handyman aligns them flush with the starting row. When nailing, he pays attention to the connection to margins and eaves parts. For the second row, he removes half a tongue from the starting shingle. The laying of the series begins at the edge of the page, with the lower end of the tongue lying flush with the sheet cut points of the previous row. Butt joints must not be on top of each other. Therefore, for each additional row, remove half a tab.

8. Covering ridge with single shingles

For a roof with ridge, the last step is the ridge laying. Individual shingle pieces cover the tip waterproof. This is done according to the principle of double coverage. The ridge pieces evenly overlap the connection rows on all sides.

Building a garden house: what does it cost?

more

We answer these and many other questions in our price radar around gardening.

Roofing flat roofs: what does it cost?

These and many other questions we answer in our price radar around the topic flat roof.

Dispose of roofing felt: what does it cost?

These and many other questions we answer in the

Dismantling a flat roof: what does it cost?

These and many other questions we answer in the price radar around the topic of flat roof insulation.

Building a bicycle shelter: what does it cost?

These and many other questions we answer in the price radar around the topic of bicycle shelter.

Build a slide: what does it cost?

These and many other questions we answer in the price radar around the topic of slide build.

Swing building: what does it cost e s?

These and many other questions we answer in the price radar around the topic of building a swing.

Building Sandkastenl: what does it cost?

These and many other questions we answer in the price radar around the topic of building sandbox.

Laying trapezoidal sheet: what does it cost?

We answer these and many other questions in the price radar around the subject of trapezoidal sheet metal.

Roof damage repair: what does it cost?

We answer these and many other questions repair in price radar around the topic of roof damage.



Video: DIY - Building a Ramada|

Share:


Comments